F.N. Sheppard & Co. | Belting specialist
F.N. Sheppard & Co. | Belting specialist
All Categories > Timing Belts > Urethane Timing Belts > Profiled/Cleated Belts; Profile Selector Guide  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Profiled/Cleated Belts; Profile Selector Guide



Timing Belts can provide exceptionally accurate synchronized conveying of products. Ideal for assembly, packaging, inserting and other automation applications. Timing belts are available in any length and can be specified in one tooth increments.

F. N. Sheppard timing belts have been used extensively as reliable profiled timing belts. The requirements in automation and material handling are diverse. Often, the designer is challenged to come up with innovative concepts to solve differing requirements depending on the product to be conveyed and function to be solved.

We offer an extensive line of synchronous belts and a wide selection of stock profiles. It allows for innovative design solutions for dividing, stepping and positioning.

When you are confronted with a drive or conveying problem, just call on us. A quick phone call can allow us to assist you in finding the desired solution or we can provide you with our suggestions.

Profiles are commonly referred to as lugs, cleats, pockets and attachments. Profiles are transverse raised sections on the outer surface of a belt used to hold, stabilize, position or transport a product. Profiles are available in many compounds and are applied in various ways. Various ways include: molding, thermal-welding, bonding and machining. Hundreds of profile designs are available from F. N. Sheppard's mold inventory. Our Applications Engineers can work with you to design any profile to meet your specific reguirements. Tooling charges are minimal for most new customized designs. Drawings of some of the profiles are shown in this catalog. Profiles allow for precise indexing with accurate placement on synchronous base belts. This synchronization is not attainable with flat belts.





Profile Spacing Tolerance  · General Information  · Types of Profiles

Profile Spacing Tolerance
Profile Spacing Over Tooth Non-cumulative Not Over Tooth
0.2" ≤ A < 1.0"
5mm ≤ A < 25.4mm
±0.015"
±0.38mm
±0.020"
±0.5mm
1.0" ≤ A < 9.0"
25.4mm ≤ A < 228.6mm
±0.020"
±0.5mm
±0.025"
±0.6mm
9.0" ≤ A < 18.0"
228.6mm ≤ A < 457.2mm
±0.025"
±0.6mm
±0.030"
±0.8mm
18.0" ≤ A < 27.0"
457.2mm ≤ A < 685.2mm
±0.030"
±0.8mm
±0.035"
±0.9mm
27.0" ≤ A < 36.0"
685.8mm ≤ A < 914.4mm
±0.035"
±0.9mm
±0.040"
±1.0mm
For spacing greater than 36.0" add 0.006" per ft.

For spacing greater than 914.4mm, add 0.15mm per 305mm.

Tighter tolerances on profile spacing are available. Please contact an F. N. Sheppard Applications Engineer for more information.




General Information

Spacing of Profiles

It is recommended but not necessary that the profile spacing (A) correspond with the pitch of the belt teeth. This allows for the best spacing tolerances, and minimizes the effects of the belt's overall length tolerance on the profile spacing. Profiles can be spaced on other than pitch increments. However, if non-pitch spacing is used, the cumulative tolerance of the belt length must be considered.

Position and Thickness of Profiles

The most important consideration while dimensioning a profile is the size of the base of the profile, (the "foot" of the profile), and the position of the profile on the belt.

The profile thickness can effect the flexibility of the belt and can determine the minimum allowable pulley diameter. The flexibility of the belt can be maximized, however, by positioning the profile directly over the tooth of the belt. As the thickness of the foot of the profile increases, the minimum pulley diameter must be increased according to the table.

Number of Pulley Teeth (Over A Tooth)

Profile "Foot"
Thickness
Inch 1/16 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4
mm 1.60 3.00 5.00 6.00 8.00 10.00 11.00 13.00 16.00 19.00
Pitch XL   10 10 18 25 40 50 60 100 - -
L   12 12 12 18 30 40 50 60 100 -
H   14 14 14 14 18 25 35 45 80 100
XH   18 18 18 18 18 18 18 20 35 50
T5 & AT5   12 12 18 25 40 50 60 100 - -
T10, AT10, ATL10   16 16 16 16 18 25 35 45 80 100
T20, AT20, ATL20   18 18 18 18 18 18 18 20 35 50
HTD® 5 & STD 5   12 12 16 25 40 50 60 100 - -
HTD® 8 & STD 8   14 14 14 18 30 40 50 60 100 -

Number of Pulley Teeth (Not Over A Tooth)

Profile "Foot"
Thickness
Inch 1/16 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4
mm 1.60 3.00 5.00 6.00 8.00 10.00 11.00 13.00 16.00 19.00
Pitch XL   12 30 45 50 60 100 - - - -
L   12 20 40 45 55 60 70 80 100 -
H   14 14 25 30 45 50 55 65 80 100
XH   18 18 20 30 40 45 50 54 58 60
T5 & AT5   12 30 45 50 60 100 - - - -
T10, AT10, ATL10   16 20 30 40 45 50 55 65 80 100
T20, AT20, ATL20   18 18 20 30 40 45 50 54 58 60
HTD® 5 & STD 5   14 30 45 50 60 100 - - - -
HTD® 8 & STD 8   14 20 40 45 55 60 70 80 100 -

Urethane Welded Profile

The strength of the profile is affected by the type and direction of the force applied to it. Under high loads, the failure mode will normally be either bending and distortion of the profile and belt, or in some cases, the urethane may actually tear. With a load introduced against the profile at a point 1/4" above the belt surface, the strength of the profile is 2,500 lbs. per square inch of welded foot area, or 1724 N/cm2. Our Technical Department would like to assist you with determination of profile strength.

Profile Strength

There are many variables to consider when figuring the strength of the profile. Variables include; method of attachment, compound of profile, belt construction, type of force, and direction of force. F. N. Sheppard has the largest selection of belts and profiles available and many methods of attaching profiles. Your application and other variables are the major factor for considering what method of attachment to use.


Types of Profiles

Wide Base Profiles

Some applications require profiles that are tall with a wide base, or need to maintain rigidity. An unwelded gusset, foot or feet would allow for flexing around a pulley, yet remain rigid when loaded or in the linear position.

Profiles With Inserts

Male and Female metallic inserts can be molded into the profiles. The actual inserts can be manufactured by F. N. Sheppard or supplied by the customer.

Profiles With Holes

Holes or slots can be molded, perforated or drilled into the profile. Holes are typically used as a means for securing other attachments. Metal or plastic style bushings may be incorporated into the hole to provide strong support. Contact our Technical Department for hole tolerances.

Profile Flashing

Depending on the process used to incorporate profiles, there may or may not be any flashing at the foot of the profile. Contact our Technical Department for details.


 MORE IMAGES 

·  Gusset Style Profiles

·  Gusset Style Profiles (Side View)

·  Wide Base Profiles

·  Wide Base Profiles (Side View)

·  Profile with Female Insert

·  Profile with Male Insert

·  Profile with Bushing Insert

·  Profile with Bolt-On Holes

·  Profile with Flashing

·  Profile with Flashing (Zoom)

·  Profile with Flashing Removed (Zoom)